Completed project · October 2026

Polyurea Flake Garage Floor in Libertyville, IL

We put a polyurea flake floor in Coyote, with a slip-resistant topcoat and coated vertical edges, into a 2-car garage in Libertyville.

  • 5.0 · 122 Google reviews
  • Lifetime warranty
  • Licensed & insured
Finished polyurea garage floor with Coyote flake blend and glossy topcoat

What we did

This was a 2-car garage on new concrete, which is about as good a starting point as we get. There were no cracks to chase and no old coating to strip off, so the whole job could go into prep and the new system. The floor measured 440 sq ft, including the outside edge. Along the base of the walls there were also 40 linear feet of vertical concrete, the curbs and exposed slab faces, that we planned to coat along with the floor.

Even new concrete gets ground. A fresh slab carries a smooth surface sheen that a coating can't grab well, so we used diamond grinding across the floor to take it off and open up the surface. We grind instead of acid-etching because grinding gives an even profile, the texture a coating bonds to, over the whole slab. We profiled the vertical faces too, so the coating would hold at the floor-to-wall transition as well as it does on the flat.

Next came the polyurea garage floor coating itself. The polyurea base coat went down first, and we broadcast Coyote flake into it to rejection, which means we kept adding flake until the wet base couldn't take any more. After that we scraped and vacuumed off the loose flake and applied a clear polyaspartic topcoat, with aluminum oxide grit broadcast into it across all 440 sq ft for better traction. The 40 feet of vertical surfaces got the same system, giving one continuous seal where floor meets wall, and we took care of the wooden step as part of the same job.

The install took one day. The floor was walkable after about 12 hours and ready for full use, cars included, after about 48 hours. The aluminum oxide adds grip, though any floor can still get slick with water, snow or oil, so it's worth keeping it clean and dry. If your garage sits on newer concrete with no damage, a job like this stays simple: the effort goes into grinding and getting each layer right, not into repairs.

Services on this job

After: Polyurea Coyote flake garage floor in Libertyville, IL Before: Polyurea Coyote flake garage floor in Libertyville, IL
Before & after: drag to compare

How we installed it

  1. 1Polyurea (Base Coat)
  2. 2Decorative Flakes
  3. 3Polyaspartic (Top Coat)
  1. Surface Preparation

    • Remove surface sheen and contaminants
    • Diamond grinding for proper surface profiling and adhesion
    • Repair cracks and patch imperfections
  2. Base Coat & Flake Application

    • Apply Polyurea base coat
    • Broadcast decorative flakes 100% to rejection
  3. Top Coat & Cleanup

    • Scrape and vacuum excess flakes
    • Apply clear Polyaspartic top coat
    • Job site cleanup

Also on this job

  • Vertical Surface Coating (40 ln ft) — Vertical concrete surfaces (toe-kicks, curbs, exposed slab faces) mechanically profiled and coated with the same polyurea/polyaspartic system applied to the horizontal slab, producing a continuous monolithic seal at the floor-to-wall transition.
  • Slip Resistance (aluminum oxide) (440 sq ft) — Aluminum-oxide aggregate broadcast into the topcoat to raise the coefficient of friction and improve underfoot traction.
  • Wooden step
  • Credit card fees 3%

Project photos

More from our Mundelein team

Had work done by our Mundelein office?

Scan the code or leave a Google review. It helps neighbors choose with confidence.

Questions about this project

How much did this garage floor coating cost in Libertyville?

This 440 sq ft 2-car garage, including 40 linear feet of vertical coating and slip resistance, came to $2,912.84. A standard two-car garage of roughly 400–500 sq ft usually runs $2,000–$3,500, and polyurea-polyaspartic flake is typically about $5.50–$7 per sq ft installed. We give an exact price only after an in-person inspection.

Does new concrete need to be ground before it's coated?

Yes. On this Libertyville job the slab was new with no cracks, and we still diamond ground it to remove the surface sheen and give the coating a proper profile to bond to. Our prep always starts with diamond grinding, followed by crack and pit repair where the concrete needs it.

How soon can I park on a new polyurea garage floor?

On this garage the install took one day, the floor was walkable after about 12 hours, and it was ready for full use, cars included, after about 48 hours. Temperature and humidity can change cure times, so we list them on each job's estimate.

What flake colors can I choose from?

This floor was done in the Coyote blend. We offer 29 flake color blends, and we can bring samples to your free on-site estimate so you can see them on your own concrete. For a free estimate, call our Mundelein team at (847) 999-6330.

Want a floor like this in Libertyville?

Free on-site estimates from our Mundelein office. Call (847) 999-6330 or book online.

© 2026 Concrete Shield Coatings Inc. All rights reserved. | Terms & Conditions | Privacy Policy