Completed project · November 2026

Polyurea Flake Garage Floor in Glenview, IL

We coated an 800 sq ft two-car garage floor in Glenview with a polyurea flake system in the Coyote blend, plus 100 linear feet of vertical edges.

  • 5.0 · 122 Google reviews
  • Lifetime warranty
  • Licensed & insured
Completed Coyote flake polyurea garage floor with satin sheen and coated curb edge

What we did

When we walked into this two-car garage, we found new concrete with no cracks and no old coating to strip. That's about as good a starting point as we get. With a clean slab, the job came down to prepping it right and covering the full 800 square feet, which took in the outside edge, along with 100 linear feet of vertical concrete where the slab meets the walls. It also meant the whole install could fit into a single day.

Even new concrete needs work before a coating goes on. A fresh slab has a smooth surface sheen that a coating can't grip well, so we diamond ground the floor to take that sheen off along with any contaminants. Grinding leaves a profile, a texture a bit like coarse sandpaper, that the base coat can lock into. That's why we choose diamond grinding over acid etching: it's more controlled and gives a consistent surface. The vertical edges were profiled too, so they'd take the coating the same way.

Next came the polyurea base coat, the layer that bonds to the concrete. We broadcast Coyote flake into it until the floor wouldn't hold any more, which we call broadcasting to rejection, so there are no thin or bare spots. After it set, we scraped and vacuumed the loose flakes and applied a clear polyaspartic topcoat. Aluminum oxide grit went into that topcoat across all 800 square feet for better traction underfoot. The same system ran up the 100 linear feet of vertical surfaces, sealing floor and edges as one continuous coat.

Start to finish, the install took 1 day. The homeowner could walk on the floor after about 12 hours, and it was ready for full use, cars included, after about 48 hours. The added grit helps with traction, though a wet or oily floor still calls for normal care. If you've got a newer slab with no cracks or old coating, your project would look a lot like this one, with the time going into prep and the coating itself instead of repairs.

Services on this job

After: Polyurea Coyote flake garage floor in Glenview, IL Before: Polyurea Coyote flake garage floor in Glenview, IL
Before & after: drag to compare

How we installed it

  1. 1Polyurea (Base Coat)
  2. 2Decorative Flakes
  3. 3Polyaspartic (Top Coat)
  1. Surface Preparation

    • Remove surface sheen and contaminants
    • Diamond grinding for proper surface profiling and adhesion
    • Repair cracks and patch imperfections
  2. Base Coat & Flake Application

    • Apply Polyurea base coat
    • Broadcast decorative flakes 100% to rejection
  3. Top Coat & Cleanup

    • Scrape and vacuum excess flakes
    • Apply clear Polyaspartic top coat
    • Job site cleanup

Also on this job

  • Vertical Surface Coating (100 ln ft) — Vertical concrete surfaces (toe-kicks, curbs, exposed slab faces) mechanically profiled and coated with the same polyurea/polyaspartic system applied to the horizontal slab, producing a continuous monolithic seal at the floor-to-wall transition.
  • Slip Resistance (aluminum oxide) (800 sq ft) — Aluminum-oxide aggregate broadcast into the topcoat to raise the coefficient of friction and improve underfoot traction.

Project photos

More from our Northbrook team

Had work done by our Northbrook office?

Scan the code or leave a Google review. It helps neighbors choose with confidence.

Questions about this project

How much did this Glenview garage floor coating cost?

This job came to $5,000 for 800 sq ft of polyurea flake floor including the outside edge, plus 100 linear feet of coated vertical surfaces and aluminum oxide slip resistance. Polyurea-polyaspartic flake floors typically run about $5.50–$7 per sq ft installed, and a standard two-car garage of roughly 400–500 sq ft is usually $2,000–$3,500. We give an exact price only after an in-person inspection.

Does new concrete need grinding before a garage floor coating?

Yes. On this Glenview job the slab was new with no cracks, and we still diamond ground it to remove the surface sheen and contaminants. Grinding gives the base coat a profile to bond to, which matters on new and old concrete alike.

How soon can you park on a polyurea garage floor?

On this job the floor was walkable after about 12 hours and ready for full use, cars included, after about 48 hours. Temperature and humidity can change cure times, so we list them on each job's estimate.

Do you offer a warranty and color choices on garage floor coatings?

Eligible residential garage installs come with a limited lifetime warranty, and we've been licensed and insured in Chicagoland since 2010. You can choose from 29 flake color blends, like the Coyote blend used here. For a free estimate, call our Northbrook team at (847) 999-6330.

Want a floor like this in Glenview?

Free on-site estimates from our Northbrook office. Call (847) 999-6330 or book online.

© 2026 Concrete Shield Coatings Inc. All rights reserved. | Terms & Conditions | Privacy Policy